25 mm to cm
- Millimeters (mm)
- 25 mm
- Centimeters
- 2.5 cm
Checked against: Exact-fraction computation from the legal unit definitions
Convert millimeters to centimeters (mm to cm) with the exact factor, a conversion chart and worked steps.
By AdminDrafted with AI writing toolsUpdated Checked examples: 3
25 mm is about 2.5 cm. In the other direction, 1 cm ≈ 10 mm.
| Millimeters | Centimeters |
|---|---|
| 1 | 0.1 |
| 2 | 0.2 |
| 5 | 0.5 |
| 10 | 1 |
| 15 | 1.5 |
| 20 | 2 |
| 25 | 2.5 |
| 30 | 3 |
| 50 | 5 |
| 75 | 7.5 |
| 100 | 10 |
| 500 | 50 |
Exact by definition.
To convert millimeters to centimeters, multiply by 0.1; to convert back, multiply by 10. For example, 25 mm is about 2.5 cm. Displayed factors and results may be rounded.
Millimeter readings are useful for small clearances, fasteners and drawing dimensions. Retain the tolerance with the original measurement: converting the number cannot make a manufactured part more accurate. Check whether a nominal part size describes its actual measured diameter.
millimetre: 1 mm = 1/1,000 m. The metre is the SI base unit of length.
Both units are defined exactly. Calculations use 50 significant digits and round only for display.
Divide millimeters by 10 to get centimeters, which moves the decimal point one place to the left. 10 mm = 1 cm, 11 mm = 1.1 cm and 1 mm = 0.1 cm. Use it to restate a ruler, caliper or drawing measurement in centimeters.
A centimeter is ten millimeters (NIST), so on a metric ruler every tenth small mark is a centimeter. 42 mm is 4 cm and 2 mm, written 4.2 cm: the first decimal place counts whole millimeters.
Part of a millimeter goes in the second decimal place. 40.5 mm is 4.05 cm, not 4.5 cm, and 0.5 mm is 0.05 cm.
Fractions divide the same way, though some repeat: a third of a millimeter is 0.0333333333333 cm.
| Millimeters (mm) | Centimeters (cm) |
|---|---|
| 0.1 | 0.01 |
| 0.5 | 0.05 |
| 1 | 0.1 |
| 2 | 0.2 |
| 5 | 0.5 |
| 10 | 1 |
| 11 | 1.1 |
| 15 | 1.5 |
| 25 | 2.5 |
| 42 | 4.2 |
| 50 | 5 |
| 100 | 10 |
| 300 | 30 |
Rainfall, screw lengths and metric engineering drawings are given in millimeters, while everyday descriptions tend to use centimeters. 25 mm of rain is 2.5 cm, and a ruler marked to 300 mm is a 30 cm ruler.
Paper sizes are defined in millimeters too: an A4 sheet is 210 × 297 mm, or 21 × 29.7 cm.
For the reverse direction, use cm to mm, and for inch rulers, mm to inches. The length converter covers meters and other lengths; squared and cubed units go in the area converter and volume converter.
Checked against: Exact-fraction computation from the legal unit definitions
Checked against: Exact-fraction computation from the legal unit definitions
Checked against: Exact-fraction computation from the legal unit definitions
1 mm is about 0.1 cm. millimetre: 1 mm = 1/1,000 m. The metre is the SI base unit of length.
Multiply by 0.1: 25 mm × 0.1 ≈ 2.5 cm. To convert back, divide by the same factor. The factor shown may be rounded.
This calculator includes 3 worked examples with independently sourced answers. They run in the test suite, and you can run them here too.